DJ TechTools - Chroma Caps Encoder V2 Blue
2,50 €
excl VAT
In Stock
Satisfied or refunded until 15/01/2025*
Usually shipped within 5 days
+infos
DJ Spare Parts
The DJ TechTools brand is recognized in the world of Deejaying for its quality accessories! Customize your controllers, DJ mixing desk with the Encoder V2 blue version.
ARTICLE N° 54959
Specifications
-
DJ TechTools Chroma Caps Encoder V2 Blue
-
Color: Blue
-
Dimensions: Encoder knob base diameter: 18.5mm x 15.4mm height
-
Ideal for customizing your controllers or mixing console
-
Dense rubber coating
-
Material: Soft, flexible rubber to the touch
-
Non-slip for a good grip
-
Slightly rounded shapes
-
Compatible with many controllers such as Native Instruments, Pioneer and other brands (check compatibility at https://store.djtechtools.com/collections/chroma-caps-cables/products/chroma-caps-knobs-and-faders)
Presentation
DJ Techtools, the famous brand specializing in products and accessories for DJs, offers you everything you need to customize your Pioneer, Native Instruments, etc. controllers. Use them to replace the original knobs (damaged or lost), or to identify the different functions assigned thanks to different colors.
Simple to set up, simply remove the old fader and replace it with a Chroma Caps Encoder.
Simple to set up, simply remove the old fader and replace it with a Chroma Caps Encoder.
Information
Accessory Type
Controller
To go further...
Be sure to check compatibility with your controller at https://store.djtechtools.com/collections/chroma-caps-cables/products/chroma-caps-knobs-and-faders
How do you replace your caps?
We've seen enough people bend or break their hardware. The guide below is a technique to avoid any mishaps when replacing your faders or encoders. Please take your time and be careful when removing the knobs.
- Pull straight up only, do not twist or wiggle the knob while pulling. (We find it easiest to lay the controller on the floor or a lower surface to get a better vantage point and pull straight up.)
- You don't want to damage your existing knobs. The best way to do this is to use a small piece of cardboard about 1 inch square (I use the top of a cereal box because it is flexible enough to bend around the knob. (A thick towel will work too)
- If you can't grab it with your hands, don't be afraid to use a pair of grips, pliers, etc. This is where the cardboard/towel you got in #2 will come in handy.
- Put a thick card (business cards work best!) between your gear and the cap when installing. This ensures that you don't push down too hard on the caps, which could cause the cap to rub against the face of your gear. (If you notice the cap rubbing, give the cap a little tug!)
Note: This is especially important on Pioneer DJ gear!
How do you replace your caps?
We've seen enough people bend or break their hardware. The guide below is a technique to avoid any mishaps when replacing your faders or encoders. Please take your time and be careful when removing the knobs.
- Pull straight up only, do not twist or wiggle the knob while pulling. (We find it easiest to lay the controller on the floor or a lower surface to get a better vantage point and pull straight up.)
- You don't want to damage your existing knobs. The best way to do this is to use a small piece of cardboard about 1 inch square (I use the top of a cereal box because it is flexible enough to bend around the knob. (A thick towel will work too)
- If you can't grab it with your hands, don't be afraid to use a pair of grips, pliers, etc. This is where the cardboard/towel you got in #2 will come in handy.
- Put a thick card (business cards work best!) between your gear and the cap when installing. This ensures that you don't push down too hard on the caps, which could cause the cap to rub against the face of your gear. (If you notice the cap rubbing, give the cap a little tug!)
Note: This is especially important on Pioneer DJ gear!