Audio Technica - PRO35
165 €
excl VAT
including eco-part : 0,07 €
Out of stock
Contact us for delivery times
Guarantee 3
years
Jessie
Louis
Do you need help?
Wired Microphones
Instrument Microphone Cardoide clamp capacitor, Audio-Technica PRO 35, a reference in the middle!
ARTICLE N° 25442
Presentation
Pro Series The range is wide enough to meet all sound requirements, meet the challenges of its decision-complicated and enter every budget.
With the ultimate electronics and a very clear, hands microphones or dedicated Series Pro range have earned the reputation of being very good sonic quality and most durable in its class.
With the ultimate electronics and a very clear, hands microphones or dedicated Series Pro range have earned the reputation of being very good sonic quality and most durable in its class.
Other features
-
Audio-Technica PRO 35
-
Dynamic Microphone Capsule
-
Directivity: Cardioid
-
Frequency response: 50-15 000 Hz
-
Output level: -45 dB (5.6 mV) ref 1V / Pa *
-
Impedance: 250 Ohm
-
Pressure Level 145 dB SPL, 1 kHz at 1% THD
-
Dynamic (typical) 115 dB SPL at 1 kHz max.
-
Report Signal / Noise: 64 dB, 1 kHz / Pa *
-
Weight: 8g (81 grams with battery)
-
Dimensions: Length 25 mm, body diameter 10.2 mm
-
Output Connector: Type Integral 3-pin XLR M
-
Cable 1.8 m with an XLR F type connector at microphone end and an XLRM-type connector at the other end
-
Supplied Accessories: AT8418 power module UniMount, soft protective pouch
-
Ideal for miking of musical instruments and general use
-
Ideal for saxophone, brass, toms and percussion.
-
Perfect for active stage performances.
-
Excels in applications with high sound pressure levels
To find out more...
PRO 35 is intended to be used in applications
Professional for which there is already a source
external power. It requires phantom power 11
52V DC that can be provided by a mixer or a bracket or
by an independent source to be connected in series such that
phantom power AT8801 single-channel or CP8506 four
Audio-Technica channels.
An integrated high-pass filter 80 Hz to switch easily
the frequency response flat to mitigating serious. There
highpass position serves to reduce sensitivity to ambient noise
low frequency (such as traffic, air-handling systems,
etc.) to the room reverberation and coupled vibration
mechanically.
The output of the power supply module is symmetrical low
impedance, she gets on a base XLRM 3-pin. The signal
is symmetrical between pins 2 and 3, the hot spot is in two
(the positive voltage on the hot spot is generated by a pressure
Positive sound on the capsule). Ground (shield) is on the
Pin 1.
To avoid phase cancellation and poor sound
quality, all mic cables must be connected so
consistently: Pin 1-Pin 1, etc.
Avoid leaving the microphone in direct sunlight or in places
where the temperature is above 43 ° C (110 ° F) for a
extended period. Extremely high humidity should also be
avoided.
• Ideal for sax, toms, brass and percussion
• Excels in applications with SPL
high
• Ideal for stage performances not
static
• Extended frequency response makes all the nuances
subtle performance
• Clip UniMount® for precise positioning, providing
impact resistance and protecting the capsule
• Contacts of gold-plated XLRM-type connectors, resistant
corrosion
• Cardioid directivity for better insulation from the source
sound and reducing the sound side and rear
Professional for which there is already a source
external power. It requires phantom power 11
52V DC that can be provided by a mixer or a bracket or
by an independent source to be connected in series such that
phantom power AT8801 single-channel or CP8506 four
Audio-Technica channels.
An integrated high-pass filter 80 Hz to switch easily
the frequency response flat to mitigating serious. There
highpass position serves to reduce sensitivity to ambient noise
low frequency (such as traffic, air-handling systems,
etc.) to the room reverberation and coupled vibration
mechanically.
The output of the power supply module is symmetrical low
impedance, she gets on a base XLRM 3-pin. The signal
is symmetrical between pins 2 and 3, the hot spot is in two
(the positive voltage on the hot spot is generated by a pressure
Positive sound on the capsule). Ground (shield) is on the
Pin 1.
To avoid phase cancellation and poor sound
quality, all mic cables must be connected so
consistently: Pin 1-Pin 1, etc.
Avoid leaving the microphone in direct sunlight or in places
where the temperature is above 43 ° C (110 ° F) for a
extended period. Extremely high humidity should also be
avoided.
• Ideal for sax, toms, brass and percussion
• Excels in applications with SPL
high
• Ideal for stage performances not
static
• Extended frequency response makes all the nuances
subtle performance
• Clip UniMount® for precise positioning, providing
impact resistance and protecting the capsule
• Contacts of gold-plated XLRM-type connectors, resistant
corrosion
• Cardioid directivity for better insulation from the source
sound and reducing the sound side and rear
You may also like
Spotlight on
Founded in 1962, Japan's Audio-Technica is a leading manufacturer of AT4033, AT4041 and Artist Elite studio and stage microphones, AT2020 USB+ podcast microphones, professional wireless systems, ATH-M series headphones, AT-LP140XP turntables and DJ accessories. Developments such as Uniguard's anti-RFI technology, which protects microphones from WiFi, Bluetooth and other modern sources of radio interference, demonstrate their commitment to providing musicians and engineers with the high-quality sound they've come to expect.
