Radial - Tonebone Bassbone OD
This product is no longer available for sale
These models in stock may be of interest to you:
482,50 €
excl VAT
including eco-part : 0,90 €
Guarantee 3
years
Fred
Eric
Do you need help?
Bass Effects
2-channel preamplifier for electric bass with bass overdrive and Wet-Dry control for lots of character, load correction for Vintage bass, piezo booster for double bass. The Bassbone OD, the world's most powerful bass preamp in a single pedal.
ARTICLE N° 55038
Presentation
The Bassbone OD is a bass preamp with 2 instrument inputs, each of which has its own level control, a super powerful interactive passive EQ and a low frequency filter to help eliminate resonances.
Channel A is equipped with a PZB footswitch which increases the sensitivity and loading to 10 Mohms in order to optimize the response for the piezoelectric sensors regularly used on the double bass.
Channel B, for its part, acts on the load correction (impedance) which aims to optimize the response of a passive instrument such as a vintage electric bass.
Switching between channels is done using the footswitch and the 2 channels can be mixed by pressing the blend switch, if a humbucker pickup system is used.
Channel A is equipped with a PZB footswitch which increases the sensitivity and loading to 10 Mohms in order to optimize the response for the piezoelectric sensors regularly used on the double bass.
Channel B, for its part, acts on the load correction (impedance) which aims to optimize the response of a passive instrument such as a vintage electric bass.
Switching between channels is done using the footswitch and the 2 channels can be mixed by pressing the blend switch, if a humbucker pickup system is used.
Other features
-
Radial Engineering Tonebone BASSBONE OD
-
2-channel preamplifier for electric bass with bass overdrive
-
Discrete Class A circuit, low noise FET input
-
Frequency response 20Hz ~ 18kHz
-
THD 0.05% @ -15dBu
-
Intermodulation distortion 0.2% @ -20dBu
-
Dynamic range 85dB
-
Input impedance A 220K/10M
-
Input impedance B Variable from 22K to 1.8M
-
Output impedance 300 Ohms
-
Max input +7 dBu
-
Gain - boost drive 0 to 25 dB
-
Gain - PZB boost +10dB channel A
-
Clip output +10dBu
-
Noise level -100dB
-
EIN -92dBu
-
Connections:
-
High impedance instrument jack output
-
3.5mm jack headphone output, mono with volume control
-
Microphone level XLR balanced output
-
Standard AES output
To find out more...
The Bassbone OD also features an instrument jack output (6.35 mm) for driving an amp on stage and a low-impedance balanced DI output for a PA system.
The XLR output can be assigned 'pre or post' effects depending on the engineer's preferences.
A dedicated 'buffered' tuner output works with the MUTE footswitch for quiet tuning on stage.
For bassists who use effects, the 2 input channels can share the same pedals by connecting via the effects loop. All enhanced by an onboard overdrive section with DRIVE, LEVEL and TONE controls. A 'wet/dry' mix allows you to add a slight grain similar to an Ampeg SVT or a big distortion if desired.
The OD pedal can be assigned to loop, overdrive or both.
Finally, a built-in headphone amp with jack output (3.5 mm) allows you to use the Bassbone on the bus for long journeys between concerts.
The XLR output can be assigned 'pre or post' effects depending on the engineer's preferences.
A dedicated 'buffered' tuner output works with the MUTE footswitch for quiet tuning on stage.
For bassists who use effects, the 2 input channels can share the same pedals by connecting via the effects loop. All enhanced by an onboard overdrive section with DRIVE, LEVEL and TONE controls. A 'wet/dry' mix allows you to add a slight grain similar to an Ampeg SVT or a big distortion if desired.
The OD pedal can be assigned to loop, overdrive or both.
Finally, a built-in headphone amp with jack output (3.5 mm) allows you to use the Bassbone on the bus for long journeys between concerts.
