Audio Technica - AT4022
314,17 €
excl VAT
including eco-part : 0,07 €
Out of stock
Guarantee 3
years
Anais
Tristan
Do you need help?
Static Microphone
polarized cardioid condenser microphone, a quality / price simply unbeatable
ARTICLE N° 22252
Presentation
The clean design AT4022 is designed for miking of instruments such as piano, acoustic guitar and other acoustic instruments.
Marked by a minimalist design, the recording microphone AT4022 omnidirectional condenser perfect for miking instruments such as piano, acoustic guitar and other acoustic instruments. With its flat frequency response and wide dynamic range and high, the AT4022 model is ideally suited for critical applications in the studio and live and easily withstands high sound pressure levels.
The omni directional microphone it preserves the sound color of the recording location and ensures a flat frequency response with no proximity effect. Its low-mass diaphragm improves transient response and reduces the transfer of mechanical noise and handling.
Marked by a minimalist design, the recording microphone AT4022 omnidirectional condenser perfect for miking instruments such as piano, acoustic guitar and other acoustic instruments. With its flat frequency response and wide dynamic range and high, the AT4022 model is ideally suited for critical applications in the studio and live and easily withstands high sound pressure levels.
The omni directional microphone it preserves the sound color of the recording location and ensures a flat frequency response with no proximity effect. Its low-mass diaphragm improves transient response and reduces the transfer of mechanical noise and handling.
Other features
-
Capsule: permanently polarized condenser Fixed-charge with fixed plate
-
Directionality: Omnidirectional
-
Frequency response: 20-20 000 Hz
-
Output level: 80 Hz, 12 dB / octave
-
Sensitivity: 34 dB (19.9 mV) ref 1V / Pa
-
Impedance: 250 Ohm
-
Maximum Sound Pressure: 146 dB SPL, 1 kHz at 1% THD ; 156 dB SPL, with? 10 dB (nominal)
-
Dynamic: 133 dB SPL at 1 kHz max.
-
Report Signal / Noise: 81 dB, 1 kHz / Pa
-
Requiremens Phantom Power: 48V DC, 3.0 mA typical
-
Weight: 124 g
-
Dimensions: Length 144.0 mm (5.67 inches) maximum body diameter 21.0 mm (0.83 in)
-
Output Connector: XLRM-type Integral 3-pin
-
Accessories: AT8405a clamp threaded 5/8 "-27; windscreen; portable protection
-
Outstanding performance and rugged construction ideal for critical applications in the studio and live
-
High sound pressure level, exceptional dynamic range
-
Flat frequency response and extended
-
High Pass Filter 80 Hz and 10 dB pad
-
Omni-directional sound pick-up for optimal atmospheres
-
Very low self noise - ideal for digital recording equipment
-
Excellent reproduction of low frequency sound
-
Low mass capsule for a great transient response
To find out more...
The AT4022 is intended for use in applications
Professional for which there is already a source
external power. It requires 48V phantom power
DC that can be provided by a mixer or a handheld or
an independent source to be connected in series such as
phantom power AT8801 single-channel or CP8506 four
Audio-Technica channels.
The output of the microphone is symmetrical low impedance, XLR
male, 3 pins. The signal is symmetrical between pins 2 and 3,
the hot spot is two (the positive voltage on the hot spot is
generated a positive sound pressure on the capsule). There
ground (shield) is on pin 1.
To avoid phase cancellation and poor sound
quality, all mic cables must be connected so
consistently: Pin 1-Pin 1, etc.
A high pass filter integrated 80 Hz allows easy switching from
flat frequency response in mitigating serious. The position
highpass is used to make the microphone less sensitive to the "pops"
when used in proximity of voice. It also serves to
reduce sensitivity to low-frequency ambient noise (such
traffic, air-handling systems, etc.), Reverb
the room and mechanically coupled vibrations.
Avoid leaving the microphone in direct sunlight or in places
where the temperature is above 43 ° C (110 ° F) for a period
extended. Extremely high humidity should also be avoided.
Professional for which there is already a source
external power. It requires 48V phantom power
DC that can be provided by a mixer or a handheld or
an independent source to be connected in series such as
phantom power AT8801 single-channel or CP8506 four
Audio-Technica channels.
The output of the microphone is symmetrical low impedance, XLR
male, 3 pins. The signal is symmetrical between pins 2 and 3,
the hot spot is two (the positive voltage on the hot spot is
generated a positive sound pressure on the capsule). There
ground (shield) is on pin 1.
To avoid phase cancellation and poor sound
quality, all mic cables must be connected so
consistently: Pin 1-Pin 1, etc.
A high pass filter integrated 80 Hz allows easy switching from
flat frequency response in mitigating serious. The position
highpass is used to make the microphone less sensitive to the "pops"
when used in proximity of voice. It also serves to
reduce sensitivity to low-frequency ambient noise (such
traffic, air-handling systems, etc.), Reverb
the room and mechanically coupled vibrations.
Avoid leaving the microphone in direct sunlight or in places
where the temperature is above 43 ° C (110 ° F) for a period
extended. Extremely high humidity should also be avoided.
Videos
You may also like
Spotlight on
Founded in 1962, Japan's Audio-Technica is a leading manufacturer of AT4033, AT4041 and Artist Elite studio and stage microphones, AT2020 USB+ podcast microphones, professional wireless systems, ATH-M series headphones, AT-LP140XP turntables and DJ accessories. Developments such as Uniguard's anti-RFI technology, which protects microphones from WiFi, Bluetooth and other modern sources of radio interference, demonstrate their commitment to providing musicians and engineers with the high-quality sound they've come to expect.
